Bygone Wagons

3d Printed representations of UK rolling stock.

GWR Morel wagon $25 plus post

3D Printed representation of a GWR Morel wagon used to carry marine propellers or wheels. Chassis and brake gear is printed as well. Printed using PLA+ and painted with an acrylic primer ready to finish further.

Dapol 14mm wheels running in romford bearings.

Tension lock couplers in nem pockets.

Comes with a flywheel as a load.

GWR Morel wagon, used for carrying marine propellor's or wheels.

GWR DD1 water tank wagon $25 plus post.

3D Printed representation of a GWR DD1 water tank wagon.

Printed using PLA+ and painted with a primer.

Dapol 12mm wheels running in brass top hat bearings. Tension couplers in nem pockets, Kadees fit as well.

GWR DD1 Water tank wagon

GWR Cartruck Vehicle Wagon $25 plus post.

3D Printed representation of a GWR Cartuck vehicle wagon Chassis and brake gear is printed as well. Printed using PLA+ and painted with an acrylic primer ready to finish further. Black and Grey available. Dapol 12mm wheels running in brass top hat bearings. Tension couplers in nem pockets.

GWR Cartruck wagon

GWR 3 AXLE "Dyson" WAGON $40, add a Ro Ro Tanker for $20 plus postage

3d Printed representation of a 3 axle wagon and roll on roll off milk tanker.

Wagon is all printed assembled and primed, with 12mm disc wheels and nem pockets and couplers.

Tanker is supplied as a kit, unpainted so you can easily do your own livery, simple assembly using cyano glue. Pins and wire included which allow for accurate and easy assembly.

Wagons have been run on my layout which does have some less than perfect track, they might benefit from some more grams in weight, but why pay post on extra weight!.

GWR RO-RO-MILK TANKER AND WAGON

GWR Long wheelbase 3 axle "Dyson"wagon $40, add a ro-ro milk tanker for $25 plus postage.

3d Printed representation of a 3 axle wagon and roll on roll off milk tanker. Wagon is all printed assembled and grey primed, with 12mm disc wheels and nem pockets and couplers.

Tanker is supplied as a kit, unpainted so you can easily do your own livery, simple assembly using cyano glue. Pins and wire included which allow for accurate and easy assembly.

Wagons have been run on my layout which does have some less than perfect track, they might benefit from some more grams in weight, but why pay post on extra weight!.

GWR 15 ton crane match wagon - $45 plus post

3D Printed representation of a GWR 15 ton crane match wagon. Chassis and brake gear is printed as well. Printed using PLA+ and painted with a grey primer. Dapol 12mm wheels running in brass top hat bearings. Tension couplers in nem pockets, Kadees fit as well. Shown with a part built Dapol crane as a guide. Would suit the upcoming Oxford rail 15 ton crane.

 

Body only to add to your own wagon - $10

GWR 15 ton crane match wagon

Body only to add to your own wagon.

WD WARFLAT Wagon. $45 plus postage.

WD Warflat wagon, all 3d printed using coloured filament so no paint on this. Ideal to do a dirty wash to tone them down, or leave as factory fresh.

3 hole wheels running in romford bearings so free running.

Also an ex WD version without jacks used for general freight, grey primed and with bolsters to make your own loads up.

The Sherman tank can be added for $15.

This is a licensed print from M Bergman I print myself.

https://www.thingiverse.com/m_bergman/designs

 

WD Rectank wagon $45 plus postage.

WD Rectank wagon, all 3d printed using coloured filament so no paint on this. Ideal to do a dirty wash to tone them down, or leave as factory fresh. All metal wheels running in romford bearings so free running. Also an ex WD version without jacks used for general freight, grey primed and with bolsters to make your own loads up. The MKIV tank can be added for $15. This is a licensed print from M Bergman I print myself. The side gun pods are not fitted but supplied.

https://www.thingiverse.com/m_bergman/designs

WD Warwell wagon.......$45 plus postage

WD Warwell wagon, used to transport the Sherman tank which was part of the Lend-Lease scheme during WW2.

All 3d printed using coloured filament so no paint on this. Ideal to do a dirty wash to tone them down, or leave as factory fresh. 3 hole wheels running in romford bearings so free running. Also an ex WD version without jacks used for general freight, grey primed and with bolsters to make your own loads up. The Sherman tank can be added for $15. This is a licensed print from M Bergman I print myself. https://www.thingiverse.com/m_bergman/designs